Damper settings for ART adj

Renault & Alpine General Discussion

Moderators: eastlmark, BIG_MVS, phildini, Test Moderator, Alpineandy

User avatar
User

steveatyork

Rank

Non Member

Posts

369

Joined

Sun Jan 30, 2005 7:16 pm

Location

York,UK


Has thanked: 0 time
Been thanked: 0 time

Damper settings for ART adj

Postby steveatyork » Sat Oct 08, 2005 7:52 am

Hoping Dave or Peter will answer this, can you give a starter for the damper settings on the adj coil-overs, got em on last week and just set them all at 10 clicks, way to bouncy at the front :cry: weather permiting was going to have a play around over the weekend
Renault Spider, Marcos Mantis, TR6...
User avatar
User

simontaylor

Rank

Non Member

Posts

5602

Joined

Thu Apr 15, 2004 12:33 pm

Location

Fleet, Hampshire


Has thanked: 44 times
Been thanked: 56 times

Postby simontaylor » Sat Oct 08, 2005 9:00 am

I'd guess, just wind em up to the hardest setting and start from there.
1986 : '86 GTA v6 BW-EFR turbo, with Adaptronic ECU
Firsts at
2007 : Gurston Down & RAOC Champion
2008 : Rushmoor & Eelmoor & ACSMC Hillclimb class Champion
2009 : Longcross & Eelmoor
2010 : Crystal Palace & Eelmoor
2016 : Rushmoor & 5th O/A
User avatar
User

peterg

Rank

Non Member

Posts

2501

Joined

Wed Apr 14, 2004 10:26 pm

Location

Cumbria


Has thanked: 0 time
Been thanked: 0 time

Postby peterg » Sat Oct 08, 2005 11:12 am

I'm running full stiffness at the front and 8 off full stiffness at the back to discourage oversteer. I'm also running the back about 5mm higher than the front.....that really helps combat understeer.
I started of full stiffness, drove it up the road and then started fiddling with the rear settings from there. At Kames last weekend :D it handled in a suprisingly neutral way......no tail out or straight on into bends at all....superb!
A jump up from the Koni set up I had :D
User avatar
User

steveatyork

Rank

Non Member

Posts

369

Joined

Sun Jan 30, 2005 7:16 pm

Location

York,UK


Has thanked: 0 time
Been thanked: 0 time

Postby steveatyork » Sat Oct 08, 2005 11:44 am

cheers will have a play once weather pics up ive also set them so it is slightly nose down did you use waxoil on the shocker body because the last set of gaz and avo coilovers i had on my 5gtt corroded badly and was a pain to adjust the hieght and damping
Renault Spider, Marcos Mantis, TR6...
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Sat Oct 08, 2005 12:38 pm

Yes, just start hard and wind back until you get the desired setting.

All the kits are zinc plated so you won't get any corrosion issues. If anything...if you oil them up, you more likely to attract grit and road salt in the winter which will sit in the threads.
Image
User avatar
User

steveatyork

Rank

Non Member

Posts

369

Joined

Sun Jan 30, 2005 7:16 pm

Location

York,UK


Has thanked: 0 time
Been thanked: 0 time

Postby steveatyork » Sat Oct 08, 2005 2:08 pm

its just that i had them on my 5 and i didnt put nothing on them(oil) and after a few months they were corroded and the adjustmensts went stiff i thinka few people had this problem on there 5s
Renault Spider, Marcos Mantis, TR6...
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Sat Oct 08, 2005 2:25 pm

There's nothing wrong with lubricating them, just check for crap stuck to the threads before winding them up and down.

All coilovers need more looking after than standard shocks just due to their nature of design. :)
Image
User avatar
User

Tony Smith

Rank

Non Member

Posts

1407

Joined

Fri Apr 16, 2004 4:50 pm

Location

Kent


Has thanked: 0 time
Been thanked: 19 times

Full hard

Postby Tony Smith » Mon Oct 10, 2005 10:30 pm

I'm running mine on full hard at the moment and its still comfortable enough for road use. To be honest for circuit use I don't think its stiff enough - would further uprated springs improve this?
Alpines - GTA 3.0 Turbo, GTA 3.0 Inj (Project DD), GTA 6.2 V8 (500 bhp) , R32 Skyline GTR, BMW Alpina B10 635 Highline, Alpina B10 E39 5 Series, Jaguar 4.2 XKR, Laguna 205GT, BMW 120d.
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Tue Oct 11, 2005 9:27 am

Could do, with maybe more damping.

If required, the adjuster knob and pin on the shocks can be taken off and and replaced with a pin 0.5mm longer. This can shift the whole load band up to much higher damping if required, but then not allow softer settings, so its horses for courses. I wanted to kit to be able to be adjusted from soft to firm with good ride control, but if a customer wants a proper hard setup, it just requires the valve pin swapping over.

Peter doesn't seem to have a problem though, and he's on the most tightest and unbalanced of tracks...

It maybe worth trying it on a track first before making any alterations.. :wink:

EDIT : Pin has to be swapped at the factory.
Last edited by David Gentleman on Wed May 10, 2006 6:19 pm, edited 2 times in total.
Image
User avatar
User

Tony Smith

Rank

Non Member

Posts

1407

Joined

Fri Apr 16, 2004 4:50 pm

Location

Kent


Has thanked: 0 time
Been thanked: 19 times

Spell check

Postby Tony Smith » Tue Oct 11, 2005 12:02 pm

Not nessessacily,


I bet that one confused the spell checker!
Alpines - GTA 3.0 Turbo, GTA 3.0 Inj (Project DD), GTA 6.2 V8 (500 bhp) , R32 Skyline GTR, BMW Alpina B10 635 Highline, Alpina B10 E39 5 Series, Jaguar 4.2 XKR, Laguna 205GT, BMW 120d.
User avatar
User

peterg

Rank

Non Member

Posts

2501

Joined

Wed Apr 14, 2004 10:26 pm

Location

Cumbria


Has thanked: 0 time
Been thanked: 0 time

Postby peterg » Wed Oct 12, 2005 9:41 pm

The ART set up is ok.....yes it could be a tiny bit stiffer, but then you risk having a car that slides everywhere. Kames (the last circuit I went to) is quite tight and twisty and the suspension was spot on. The car was very neutral, not too much roll, good grip and a second quicker (on a 90second run) than with the old set up. Too firm can be worse than too soft. You only have to look at US 'sports cars' like the Corvette to see that....suspension rock hard....spin at the drop of a hat. Certianly for road use ithe ART set up is ideal as it can be softened for everyday use.....unless you fancy employing a chiropractor!!!!!
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Wed Oct 12, 2005 9:50 pm

From this feedback, I will offer two kits, one with the current setup, and one with the different valve adjuster, though that will be for track use only though...
Image
User avatar
User

Tony Smith

Rank

Non Member

Posts

1407

Joined

Fri Apr 16, 2004 4:50 pm

Location

Kent


Has thanked: 0 time
Been thanked: 19 times

How much difference

Postby Tony Smith » Sun Oct 16, 2005 8:23 am

Is there an easy way to equate how the 2 settings would compare. If the settings with the stiffer pin (ooh er missus) started about the midway point of the softer range I would say they would make it ideal - can the pins be changed in situ?
Alpines - GTA 3.0 Turbo, GTA 3.0 Inj (Project DD), GTA 6.2 V8 (500 bhp) , R32 Skyline GTR, BMW Alpina B10 635 Highline, Alpina B10 E39 5 Series, Jaguar 4.2 XKR, Laguna 205GT, BMW 120d.
User avatar
User

Tony Smith

Rank

Non Member

Posts

1407

Joined

Fri Apr 16, 2004 4:50 pm

Location

Kent


Has thanked: 0 time
Been thanked: 19 times

Ride quality

Postby Tony Smith » Sun Oct 16, 2005 8:27 am

I drove my Skyline the other day and the GTA on full hard is very similarly damped to that with standard suspension - wheel size is up 2" from standard on both cars so its a fair comparison - GTA doesn't bump steer or tramline nearly as much though.
Alpines - GTA 3.0 Turbo, GTA 3.0 Inj (Project DD), GTA 6.2 V8 (500 bhp) , R32 Skyline GTR, BMW Alpina B10 635 Highline, Alpina B10 E39 5 Series, Jaguar 4.2 XKR, Laguna 205GT, BMW 120d.
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Re: How much difference

Postby David Gentleman » Sun Oct 16, 2005 5:08 pm

Tony Smith wrote:Is there an easy way to equate how the 2 settings would compare. If the settings with the stiffer pin (ooh er missus) started about the midway point of the softer range I would say they would make it ideal - can the pins be changed in situ?


Nope, has to be done at GAZ, but I may offer exchange dampers to help everybody out. :)
Image


  • Advertisement

Who is online

Users browsing this forum: Google [Bot] and 72 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France