JL Engineering Bi-Turbo 3.0 Project+full chassis refurb

A place to showcase your pride and joy

Moderators: eastlmark, BIG_MVS, Test Moderator

User avatar
User

John Law

Rank

Club Member

Club Member
Posts

206

Joined

Wed Sep 27, 2006 9:41 am

Location

London


Has thanked: 3 times
Been thanked: 5 times

JL Engineering Bi-Turbo 3.0 Project+full chassis refurb

Postby John Law » Thu Feb 23, 2012 10:54 pm

Safrane bi-turbo engine conversion to fit customers GTA.

Image

Image

Started off by fabricating the tubular manifold. Using 10mm laser cut flanges throughout.

Image

Cutting the exhaust tubing to construct the 3 into 1 merged collectors.

Image

Image

Collector finished with turbo flange.

Image

One side finished.

Image

Both sides finished now and off to be ceramic coated inside and out along with the exhaust housings..

Image
Last edited by John Law on Fri Jul 20, 2012 10:33 pm, edited 2 times in total.
no avatar
User

MFaulks

Rank

Non Member

Posts

1552

Joined

Sun Sep 28, 2008 4:25 pm


Has thanked: 45 times
Been thanked: 26 times

Postby MFaulks » Thu Feb 23, 2012 11:32 pm

Nice project :-) keep it coming, it's great I have a bi-turbo project to complete and this will kick me up the butt ;-)

Did you buy that Hartige engine from Ebay in the end? :-)
... A diamond is only a piece of coal that did well under pressure... PRV afflicted, may be I need to squeeze harder!!!!

https://www.facebook.com/maftecfaulks
User avatar
User

The Saint

Rank

Administrator

Posts

1128

Joined

Thu Sep 08, 2011 11:55 am

Location

Rugby Warwickshire


Has thanked: 57 times
Been thanked: 45 times

Postby The Saint » Fri Feb 24, 2012 7:17 am

Christ that looks very wide to go into the engine compartment?
The Saint.
Blue A610,
Black Smart Roadster.
SmartEDElectric Drive
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Fri Feb 24, 2012 8:30 am

8) Stuff Jonboy .
User avatar
User

si21

Rank

Non Member

Posts

2094

Joined

Mon May 09, 2005 8:24 pm

Location

S.E London


Has thanked: 3 times
Been thanked: 2 times

Postby si21 » Fri Feb 24, 2012 8:51 am

The Saint wrote:Christ that looks very wide to go into the engine compartment?


Loads of room in those swollen rear arches :lol: :lol: :lol: well enough to get my big head and shoulders in ....I should know I have had anough practice :lol: :lol: :lol:

looking fantastic Johnno must pop down one evening and black my nose ....that workshops looking sorted now too :wink:

si21
User avatar
User

andyh877

Rank

Non Member

Posts

3709

Joined

Mon Apr 18, 2005 7:11 am

Location

Alpine France


Has thanked: 1 time
Been thanked: 5 times

Postby andyh877 » Fri Feb 24, 2012 12:37 pm

MFaulks wrote:Nice project :-) keep it coming, it's great I have a bi-turbo project to complete and this will kick me up the butt ;-)

Did you buy that Hartige engine from Ebay in the end? :-)


looks like the Hartge engine i supplied
User avatar
User

John Law

Rank

Club Member

Club Member
Posts

206

Joined

Wed Sep 27, 2006 9:41 am

Location

London


Has thanked: 3 times
Been thanked: 5 times

Postby John Law » Fri Feb 24, 2012 7:47 pm

Thanks guys :D

Yes its one of the Hartge engines, Stephen has had it sitting around since getting it off Andy. Good to see it put to use.

Unfortunately its not just a straight swap, lots to be fabricated and changes made to engine mount plate, sump etc.

The turbos will be positioned in the large voids behind the inner wings.


Cheers.
JL Engineering UK, follow us at facebook.com/jlengineeringuk.
twitter- jlengineeringuk
instagram- jlengineeringuk
07840459381
no avatar
User

MFaulks

Rank

Non Member

Posts

1552

Joined

Sun Sep 28, 2008 4:25 pm


Has thanked: 45 times
Been thanked: 26 times

Postby MFaulks » Sat Feb 25, 2012 9:35 am

8) hope you got the ecu with it, make your lie easy.

...come on then, if this is not a caption competition... pic 6.. hidden bracket or local specific gravity :wink:

What else are you going to be doing to the car to go along with this, it's a red GTA isn't it?
... A diamond is only a piece of coal that did well under pressure... PRV afflicted, may be I need to squeeze harder!!!!

https://www.facebook.com/maftecfaulks
User avatar
User

John Law

Rank

Club Member

Club Member
Posts

206

Joined

Wed Sep 27, 2006 9:41 am

Location

London


Has thanked: 3 times
Been thanked: 5 times

Postby John Law » Sat Feb 25, 2012 7:02 pm

Hey Martin, the engine will be running on Adaptronic management. Going distributorless.

Hidden bracket! You know me better than that, I use 'the force' when mocking up my exhaust manifolds..

The engine belongs to Mr Miles, lots of uprating going on throughout the car. Im mainly dealing with the engine conversion and related upgrades.

Cheers
JL Engineering UK, follow us at facebook.com/jlengineeringuk.
twitter- jlengineeringuk
instagram- jlengineeringuk
07840459381
no avatar
User

MFaulks

Rank

Non Member

Posts

1552

Joined

Sun Sep 28, 2008 4:25 pm


Has thanked: 45 times
Been thanked: 26 times

Postby MFaulks » Fri Mar 30, 2012 8:04 am

Ragnotti Drift wrote:Hidden bracket! You know me better than that...


:-) :-) .. yes I did see after I posted, but it was a bit of fun :-) ...

BTW where did you go in the end to get the headers ceramic coated? Can they do the inside as well as the outside, and roughly how much did it cost? I have some mild steel headers for another application and was thinking of possibly using them for turbo use if they were suitably protected from the extreme thermal stress.

Do you have any pictures of the valve springs / setup and spring caps on this engine by any chance?
... A diamond is only a piece of coal that did well under pressure... PRV afflicted, may be I need to squeeze harder!!!!

https://www.facebook.com/maftecfaulks
User avatar
User

darrenbiggs

Rank

Non Member

Posts

1499

Joined

Thu Apr 29, 2004 1:03 pm

Location

Horley - Nr Gatwick


Has thanked: 15 times
Been thanked: 39 times

Postby darrenbiggs » Fri Mar 30, 2012 8:51 am

possibly using them for turbo use if they were suitably protected from the extreme thermal stress.


You want Starlite..... well you would do if only they family had had ever allowed it to be properly tested and commercialised.

http://www.telegraph.co.uk/technology/5 ... world.html
I'm just here for the gasoline.
no avatar
User

MFaulks

Rank

Non Member

Posts

1552

Joined

Sun Sep 28, 2008 4:25 pm


Has thanked: 45 times
Been thanked: 26 times

Postby MFaulks » Fri Mar 30, 2012 9:54 am

.
Last edited by MFaulks on Sun Jun 12, 2016 5:47 pm, edited 1 time in total.
... A diamond is only a piece of coal that did well under pressure... PRV afflicted, may be I need to squeeze harder!!!!

https://www.facebook.com/maftecfaulks
User avatar
User

John Law

Rank

Club Member

Club Member
Posts

206

Joined

Wed Sep 27, 2006 9:41 am

Location

London


Has thanked: 3 times
Been thanked: 5 times

Postby John Law » Sun Apr 01, 2012 3:48 pm

Hi Martin,

The headers and some turbo components have been coated by Cam Coat, it worked out at £380.00 including vat thats inside and out. The finish is good but it was quite a long turnaround, about 4 weeks.

I'll send you some pics of the valve springs etc or pop over have a look if you got a spare evening.

Cheers, John.
JL Engineering UK, follow us at facebook.com/jlengineeringuk.
twitter- jlengineeringuk
instagram- jlengineeringuk
07840459381
User avatar
User

John Law

Rank

Club Member

Club Member
Posts

206

Joined

Wed Sep 27, 2006 9:41 am

Location

London


Has thanked: 3 times
Been thanked: 5 times

Postby John Law » Sun Apr 01, 2012 5:36 pm

Little update as to how the project is progressing.

Image

The sump, windage tray, oil pickup and sandwich plate need removing and are being replaced by new/reconditioned GTA turbo parts.

Image

Image

New, rare as hens teeth A610 inlet manifold is going to be used with 440cc injectors and single throttle body.

Image

These -10JIC fittings are tig welded to both sides of the sump and act as oil drain returns for the turbos. Just needs vapour blasting and its ready for buttoning up.

Image

Image

Parts back from the ceramic coaters, trial fitting the turbo oil feeds, all fits well so far. Next on the agenda is fabricating the boost pipes and twin chargecooler setup.
JL Engineering UK, follow us at facebook.com/jlengineeringuk.
twitter- jlengineeringuk
instagram- jlengineeringuk
07840459381
no avatar
User

Jon K

Rank

Non Member

Posts

107

Joined

Sun Mar 20, 2011 9:24 pm

Location

Winchester


Has thanked: 0 time
Been thanked: 0 time

Postby Jon K » Sun Apr 01, 2012 5:57 pm

That looks great John, any idea when it is going in?
1989 GTA Turbo
1994 Land Rover Disco Pick-up
Next


  • Advertisement

Who is online

Users browsing this forum: No registered users and 30 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France